Worx Landroid Won't Charge? 5 Fixes That Work

Charging Faults and Boundary Wire Faults Look Similar but Aren't

A Landroid that won't charge and one throwing a boundary wire fault can both leave the mower stuck near the base looking equally dead, which is why it's worth confirming which one you're actually dealing with first. If the display shows a wire-related message specifically, that's a different repair — see our dedicated Worx boundary wire fault guide instead. This one covers a genuine charging failure: the mower sits at the base with a valid wire signal but simply won't take a charge.

---

Try This First (2 Minutes)

• Check the display for the exact message — a charging fault and a wire fault show different text
• Confirm the base station's power adapter is firmly seated in the outlet
• Look at the charging contact plates on the mower's underside for corrosion or grass buildup
• Manually drive the mower into the base and check it seats fully forward

---

Fix 1: Clean the Charging Contacts (Works Around 30% of the Time)

How to Fix:

1. Power off the mower
2. Inspect the contact plates on the mower's underside and the base station's charging prongs
3. Clean off corrosion or debris with a dry cloth, or fine sandpaper for stubborn buildup
4. Manually dock the mower and confirm the contacts line up flush
5. Power on and check the display for a charging status

Time: 5-10 minutes | Cost: Free | Success Rate: ~30% | Difficulty: Easy

Model notes: Applies across the standard L-series (L1500, WR147, M700) and Landroid Vision M500 — Vision's charging hardware is identical even though its navigation is camera-based.

If this doesn't work: Move to Fix 2 to check base alignment.

---

Fix 2: Re-Level and Realign the Base Station (Works Around 20% of the Time)

Ground shifts over a season — frost heave, settling soil, edging work — can leave a base tilted just enough that the mower's contacts don't seat properly even though everything looks fine.

How to Fix:

1. Check that the base station sits level and hasn't sunk or tilted since installation
2. Confirm the mower drives in fully forward, not stopping short
3. Reseat the base on firm, level ground using its mounting stakes if it's shifted
4. Test with a manual docking attempt and confirm the contacts engage on the first try

Time: 15-20 minutes | Cost: Free | Success Rate: ~20% | Difficulty: Easy

If this doesn't work: Check the base station's power supply next.

---

Fix 3: Check the Base Station Power Supply (Works Around 20% of the Time)

Safety note: Unplug the base station from mains power before inspecting the adapter, cable, or outdoor wiring connections.

How to Fix:

1. Unplug the power adapter and inspect the cable for cracks, chew marks, or water damage where it runs outdoors
2. Test the wall outlet with another device to confirm it's supplying power
3. Check any outdoor-rated extension or junction connection is dry and firmly seated
4. Reconnect the adapter and confirm the base station's status light comes on

Time: 10-15 minutes | Cost: Free, or $20-40 for a replacement adapter if damaged | Success Rate: ~20% | Difficulty: Easy

If this doesn't work: A power cycle of both the mower and base is the next simple step.

---

Fix 4: Power Cycle the Mower and Base Station (Works Around 15% of the Time)

How to Fix:

1. Power off the mower using the main switch
2. Unplug the base station from mains power for about a minute
3. Reconnect the base and let it fully initialize
4. Power the mower back on and manually dock it
5. Check the display for a charging status once seated

Time: 10 minutes | Cost: Free | Success Rate: ~15% | Difficulty: Easy

If this doesn't work: If the display shows a wire-specific message at this point rather than a charging one, switch to our dedicated boundary wire fault guide instead.

---

When DIY Won't Work - Repair vs Replace

Signs it's time for professional service:

• The base station's status light never comes on even with a confirmed working outlet and adapter
• Contacts are clean and aligned but the mower still shows no charge after several attempts
• The charging fault started right after a storm or nearby electrical work

Cost comparison: Everything above is free to check yourself, aside from a possible replacement adapter. A dealer diagnostic for a suspected internal charging circuit fault typically runs $50-90.

Warranty check: A confirmed internal fault in the base station or charging circuit is generally covered if the mower is still within its warranty period.

---

Prevent Future Charging Issues

• Clean the contact plates monthly during the mowing season
• Recheck base leveling each spring, since ground movement happens gradually over winter
• Keep the power adapter and cable off bare, damp ground
• Confirm you're reading the exact display message before troubleshooting, since a wire fault and a charging fault need different fixes

---

FAQ

How do I tell a charging fault from a boundary wire fault on Landroid?

Check the exact message on the display. A charging fault relates specifically to the base station and contacts; a wire fault mentions the perimeter signal directly. See our dedicated boundary wire guide if it's the latter.

Is a "won't charge" issue usually the battery or the base station?

The base station and its contacts cause the majority of cases. Rule those out with contact cleaning and alignment checks before assuming a battery fault.

Do I need to reset anything after cleaning the contacts?

No. Once the contacts are clean and properly seated, charging resumes automatically.

Does Landroid Vision charge differently than standard Landroid models?

No — Vision uses the same charging hardware and contacts. Its camera-based navigation is a completely separate system from charging.

How do I know if my base station has lost power entirely?

Check its status light. If it's completely off even with the adapter plugged into a known-working outlet, the fault is in the power supply itself.

Is a charging fault covered under warranty?

A confirmed internal fault in the base station or charging circuit is typically covered within the warranty period. Outlet and home wiring issues on your end aren't.